Other Brands

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete. 
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS: Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.

TIPS: Store partly-used tubes in a deep freezer. Warm up to room temperature before use again.

Odourless, non toxic and tasteless.

A favourite of RC cars enthusiasts.

By changing the silicon oil viscosity you can change the compression rate of the shock absorber

NOTE:
50 CST is less viscous than water
100 CST is a similar viscosity to water
5000 CST is much more viscous than water

A favourite of RC cars enthusiasts.

By changing the silicon oil viscosity you can change the compression rate of the shock absorber

NOTE:
50 CST is less viscous than water
100 CST is a similar viscosity to water
5000 CST is much more viscous than water

A perfect alternative to Shoe Goo!

Waterproof • Tough • Flexible

Made from Multi-Purpose Industrial Strength Original E6000 Glue

Shoe Glu is a superior no mess adhesive and sealant that easily and permanently repairs all types of footwear. It is widely used by skate boarders to keep their favourite shoes in usable condition. It is made from a synthetic rubber and it adheres to all kinds of materials, so use Shoe Glu to mend rubber soles, tears in canvas or leather tops or to stop shoe laces from fraying. It dries to a waterproof, flexible rubber, so it will repair waders and boots without breaking or cracking.

Directions

Clean damaged area. Apply glue directly over the damage as a layer.

In case of two components having come apart (such as loose soles), apply glue to both sides and keep pressed together until cured.

Glue remains flexible when cured. Full cure takes 12 hours. Clear and suitable for all colours.

Perfect for your favourite training shoes.

Cements almost anything to anything.

Waterproofs and insulates.

Never becomes brittle.

Bonds plastic, crockery, wood, metal, tile, cork, china, fabric, and others.

A great alternative to Neoprene Queen, works just as well.

Aquaprene Contact Adhesive is a fast-curing, thick, black glue. Its premium quality and properties make it perfect for repairing wetsuit and drysuit damage that regularly occurs over time with regular use. This great adhesive will enable you to make easy and durable repairs to neoprene rips, roles, leaks and split seams on wetsuit and drysuit material. 

To use, apply to both edges of a rip and bond firmly together for 20 seconds. Within 5 minutes, it should be touch dry and you will be ready to go back in the water!

An essential tool for divers, anglers, surfers, body boarders, kite surfers and sailors.

Perfect for casual watersports enthusiasts as well as professional triathletes who want to stand out.

Bonds on contact.

Dries Fast and stays Flexible.

Waterproof.

No clamping required.

Amber in colour.

50m roll of nylon tape with hot melt adhesive on the back.

Model name: T-2000X

Size: 22mm x 50m

Colour: Dark grey

Directions: Seal into position with a hot iron to cover glued and stitched seams on wetsuits and dry suits, for a perfect finish.

1m strip of nylon tape with hot melt adhesive on the back.

Model name: T-2000X

Size: 22mm x 1m

Colour: Dark grey

Directions: Seal into position with a hot iron to cover glued and stitched seams on wetsuits and dry suits, for a perfect finish.

Any length Available up to 50m

For repairing small holes and rips in trampolines.

Waterproof • Durable • Clear • Non Flammable

Directions

Clean around the damaged area. For small holes, apply a thick film (1.5mm) of glue over the damaged surface plus an extra 10mm around it and leave to cure. To fix holes larger than 5mm, cover the underside of the hole with sticky tape. Apply the glue over the top surface as a thick film. (The tape holds the glue in place as it cures.) After it has cured, remove the tape and apply another thick film of glue on the underside. Always glue up to 10mm beyond the edges of the hole. Leave for 24 hours for a full cure.

Perfect for repairing your trampoline!

* Former Gluelines Product

Ideal for patching and joining neoprene edge to edge.

Directions:

Ensure material is clean, grease free and dry. Apply a thin layer of glue to both sides. Allow to dry for 3 minutes. When touch dry, carefully align and then press the two sides together and hold firmly in place for a minute.

J-B Mini Clear Epoxy Syringe Contains 6 Ml Of Clear Epoxy And Sets In Five Minutes And Cures In 2-3 Hours.

• Adheres to metal, wood, tile, ceramic glass and china
• 1 time use
• Sets five minutes
• Cures in 2-3 hours
• JB Weld Quality

A versatile tape coated with strong adhesive on both sides, easy to tear and special backing paper makes application easier. Ideal for mounting displays, crafts, and more.

Clear and water resistant

Forms extra strong bond

Hard Plastics Clear Adhesive bonds PVC-U, ABS and High Impact Polystyrene as well as clear plastics and other materials

Quick and easy mounting for your display materials, signs and charts from Sellotape

Quick, easy to use fasteners.

Reusable thousands of times without loss of grip.

A 12 metre roll of clear Bostik sticky tape with a dispenser. Ideal for daily desk and craft use.

A PVA based adhesive. Weldbond is preferred by professional mosaic artists around the world.

It is an ideal adhesive for all types of mosaic projects using glass, ceramic, plastic, and other types of tiles.

Non-Toxic Bonds just about anything! Dries Clear Non-Flammable Water Soluble

Bonds wood, Tile, Glass, Styrofoam, Fabrics, Ceramics and much more!

Devcon Duco Plastic and Model Cement is ideal for bonding polystyrene plastic models and toys. It is good to use removable tape on areas that you do not want the cement to get on. Before the cement cures, remove the tape. Flammable, keep away from heat, sparks and open flame. Dries clear, with a tensile strength of 300 PSI. Temperature Range: 200°F.

Handling time: 10 minutes; Set time: 2 hours; Cure time: 24 hours

Super Blue® Silicone is a high performance, single component, moisture curing RTV (room temperature vulcanizing) silicone gasketing material that cures into a strong, silicone rubber that maintains long term durability and flexibility.

Super Blue® Silicone is a non-slumping, paste-like consistency which cures when exposed to moisture in the air.

Forms a tough, flexible silicone rubber gasket that resists aging, weathering; will not harden, shrink or crack.

Zap 2ml Super Glue Pen - Medium viscosity Cyanoacrylate adhesive.

ZAP-A-GAP CA+ Is the best selling instant glue in the world. The ability to bond virtually anything to anything with consistency unequalled by any other brand makes it the favorite adhesive across many varied disciplines. Widely used throughout the hobby industry, it is the absolute best and most consistent performing glue for model building and crafting. 

Helpful Hints: 
A little goes a long way! More glue doesn’t always mean a stronger joint. Only apply enough glue to evenly coat the area to be bonded when the parts are joined. Many times glue needs to be applied only to one part. Working or positioning time will vary depending on the material. Even though ZAP-A-GAP CA+ is a gap filling formula, some of it will wick into porous materials. For porous products you may have to apply more glue to get the strongest bond, it would be best to try bonding some test pieces to determine the proper amount. For modeling applications where a small fillet is desirable, bond the parts and let the glue set, then go back and create the fillet, use kicker to immediately set the glue. For critical applications test sample joints for the designed strength requirements.