Arts & Crafts

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete. 
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS: Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.

TIPS: Store partly-used tubes in a deep freezer. Warm up to room temperature before use again.

Stormseal is a seam sealer that comes in a squeezable bottle with a foam pad for easy and precise application. The liquid soaks in to pinholes, stitching and leaking seams and dries clear, leaving a flexible and waterproof surface. It contains no VOC’s and is non-toxic. It is water based but once cured it can pass through the washing machine with no problems.

DIRECTIONS

Directions. Clean area. Remove cap and brush on a generous layer Stormseal using the foam pad by gently squeezing the bottle. Allow the liquid to soak into the fabric, stitching and pin hole and then let it cure for 15-25 minutes or until clear and dry. 

A tube of Remo Tip Top Vulcanising cement and 2 Remo black vulanised rubber patches. These are the best patches and glue you can get and the best for making permenent repairs on vulcanised rubber material. They work very well on car and bicycle tyre inner tubes and some rubber boots which are made from vulcanised rubber.

Use Stormsure Flexible Repair Adhesive if the material is not vulcanised rubber.

Quick setting. Usable in just a few minutes.

Polymorph is the same as StormForm. It is a hand moudlable plastic, which comes in the form of 2mm white beads. Place a spoonful beads in a cup and add boiling water. The beads quickly melt together and become transparent. The melted plastic can be moulded by hand, rolled out into sheets and stuck onto many surfaces.

Polymorph can be reheated and remelted many times, so it is fully recycleable. It is non toxic and is also biodegradable if buried in soil

Melts at 62ºC in hot water or any other heat source. Non-toxic. Biodegradable.

Mould it into the shape you need and let it cool to room temperature.

Recycle it many times by reheating.

Cut it, drill it, stick it!

Polymorph is >99% epsilon caprolactone polyester with 1,4 butanediol.

Stormsure polymorph is a linear polycaprolactone (PCL) monomer grade with high molecular weight (about 50,000). It is a compostable and printable grade, exhibiting very good biodegradability and resistance to tear, moisture and impact. Provides flexibility, enhanced durability, high elongation and excellent low temperature performance. Offers strong adhesion to substrates, enhanced biopolymer performance, compatibility with a wide range of common thermoplastics and solubility in several common solvents. Polymorph is used in a variety of adhesive applications. It complies with EN13432.

NOW COMES IN WHITE!

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete. 
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS: Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.

TIPS: Store partly-used tubes in a deep freezer. Warm up to room temperature before use again.

Small 5g tubes containing the same as E-6000 adhesive. This synthetic rubber adhesive is the same as E600, Shoe Goo, Shoe Glu, Aquatite and Bondtite.

The adhesive will come in blank, unprinted tubes. The glue is clear and cures over a period of 6-10 hours depending on temperature and humidity.

The cured product is flexible, wear resistant, wateproof and strong.

A synthetic rubber compound which adheres well to many surfaces.

12g tubes containing the same as E-6000 adhesive. This synthetic rubber adhesive is the same as E600, Shoe Goo, Shoe Glu, Aquatite and Bondtite.

The adhesive will come in blank, unprinted tubes. The glue is clear and cures over a period of 6-10 hours depending on temperature and humidity.

The cured product is flexible, wear resistant, wateproof and strong.

A synthetic rubber compound which adheres well to many surfaces.

50m roll of nylon tape with hot melt adhesive on the back.

Model name: T-2000X

Size: 22mm x 50m

Colour: Dark grey

Directions: Seal into position with a hot iron to cover glued and stitched seams on wetsuits and dry suits, for a perfect finish.

1m strip of nylon tape with hot melt adhesive on the back.

Model name: T-2000X

Size: 22mm x 1m

Colour: Dark grey

Directions: Seal into position with a hot iron to cover glued and stitched seams on wetsuits and dry suits, for a perfect finish.

Any length Available up to 50m

A versatile tape coated with strong adhesive on both sides, easy to tear and special backing paper makes application easier. Ideal for mounting displays, crafts, and more.

Clear and water resistant

Forms extra strong bond

Hard Plastics Clear Adhesive bonds PVC-U, ABS and High Impact Polystyrene as well as clear plastics and other materials

Quick and easy mounting for your display materials, signs and charts from Sellotape

Quick, easy to use fasteners.

Reusable thousands of times without loss of grip.

Pack of 4 colours - Clear • Black • Khaki • White

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete. 
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS: Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.

TIPS: Store partly-used tubes in a deep freezer. Warm up to room temperature before use again.

500ml unbranded container of white PVA glue with dispenser nozzle and cap.Ideal for crafts and school use. A standard wood glue

Uses:

• as wood glue, PVAc is known as "white glue" and the yellow as "carpenter's glue".
• as paper adhesive during paper packaging conversion
• in bookbinding and book arts, due to its flexible strong bond and non-acidic nature (unlike many other polymers). The use of PVAc on the Archimedes Palimpsest during the 20th century greatly hindered the task of disbinding the book and preserving and imaging the pages in the early 21st century, in part because the glue was stronger than the parchment it held together.^[6]
• in handicrafts
• as envelope adhesive
• as wallpaper adhesive
• as a primer for drywall and other substrates

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete.
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS: Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.

TIPS: Store partly-used tubes in a deep freezer. Warm up to room temperature before use again.

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete.
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS: Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.

TIPS: Store partly-used tubes in a deep freezer. Warm up to room temperature before use again.

 5 litre container of white PVA glue. Ideal for crafts and school use. A standard wood glue

Uses:

• as wood glue, PVAc is known as "white glue" and the yellow as "carpenter's glue".
• as paper adhesive during paper packaging conversion
• in bookbinding and book arts, due to its flexible strong bond and non-acidic nature (unlike many other polymers). The use of PVAc on the Archimedes Palimpsest during the 20th century greatly hindered the task of disbinding the book and preserving and imaging the pages in the early 21st century, in part because the glue was stronger than the parchment it held together.^[6]
• in handicrafts
• as envelope adhesive
• as wallpaper adhesive
• as a primer for drywall and other substrates

Works great on photos, Models, Prototypes, Foam Board & Paper.

• Acid Free
• Photo Safe
• Permanent
• Quick, Easy & Clean
• Disposable, Non-refillable

BLACK AIR BRUSH BRAIDED HOSE WITH 1/8" BSP

1/8" SWIVEL FITTING AIR BRUSH RUBBER

BRAIDED AIR HOSE 3 METRE.
This braided air hose is supplied with the fittings necessary to connect to all Iwata airbrushes and the EW-440 / bd-128p / bd-132 and many, many more (all apart from the tiny 5mm badger fitting).
The hose connects directly to the airbrush one end with a 1/8" BSP - 1/8" BSP swivel nut.
The other nut is for connection to your compressor or air supply.

Stormform is a multi-purpose, reusable product which contains very tough plastic polymorph pellets which turn into a squishy and mouldable substance when heated up. This enables you to create repairs and replacements to plastic and metal parts as well as mould grips, handles, decorations, brackets, connections and much, much more. The product is very strong and can be painted to match its surroundings. Biodegradable and non-toxic!

When added to hot water, Stormform becomes mouldable and can be shaped into just about anything. Once cooled, it will solidify and become very tough.

DIRECTIONS

Add required amount of Stormform granules to a glass of hot water. The granules will turn clear and malleable. Use fingers or tools to form the required shape. Allow the substance 15-20 minutes to harden. 

TIPS

The hardened plastic can be sawed and drilled. Re-heat and reuse hundreds of times.

A small, stiff bristled brush ideal for spreading thin layers of adhesive over a wide area.

NOW COMES IN KHAKI!

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete. 
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS: Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.

TIPS: Store partly-used tubes in a deep freezer. Warm up to room temperature before use again.

Tesa 4323 general purpose paper masking tape is finely creped with a natural rubber adhesive.