Fishing

Stormsure ’TUFF Tape’ is a very strong, clear, self-adhesive, waterproof tape that is sold as individual pre-cut patches and strips of various shapes and sizes. TUFF Tape is made of a thin, but very tough, polyurethane film with a pressure sensitive adhesive and backing paper on the rear side. It has characteristics unlike many other tapes. It is waterproof and air tight. It is highly resistant to abrasion and very difficult to tear or puncture. It stretches and is elastic and it can withstand both heat and extreme cold without losing all its useful characteristics. TUFF Tape is very strong and can bind together items just by stretching the tape around the item and using the elasticity to pull the pieces tightly into place. When TUFF tape is applied to clothing it will go through regular washing machine cycles unaffected.

USES: Use TUFF Tape to quickly repair rips in waterproof clothing, ripped netting and fabrics, inflatable mattresses, canoes and RIBs, tents and awnings, sails and kites, waders, cracked buckets and other plastic containers, PVC curtain sides on trucks and warehouses.

DIRECTIONS: Ensure that the surface is clean and dry before using. Cut a suitable sized piece of TUFF Tape for your repair using good quality scissors or a sharp scalpel blade. Peel off the backing paper. Carefully position and then apply the TUFF Tape directly on top of the damage. Start at one edge and press the tape down gradually to avoid the entrapment of air bubbles. Once the TUFF Tape is in place rub it firmly with a smooth and hard object (such as the back of a spoon) to ensure the maximum adhesion to the substrate.

Stormsure ’TUFF Tape’ is a very strong, clear, self-adhesive, waterproof tape that is sold as individual pre-cut patches and strips of various shapes and sizes. TUFF Tape is made of a thin, but very tough, polyurethane film with a pressure sensitive adhesive and backing paper on the rear side. It has characteristics unlike many other tapes. It is waterproof and air tight. It is highly resistant to abrasion and very difficult to tear or puncture. It stretches and is elastic and it can withstand both heat and extreme cold without losing all its useful characteristics. TUFF Tape is very strong and can bind together items just by stretching the tape around the item and using the elasticity to pull the pieces tightly into place. When TUFF tape is applied to clothing it will go through regular washing machine cycles unaffected.

USES: Use TUFF Tape to quickly repair rips in waterproof clothing, ripped netting and fabrics, inflatable mattresses, canoes and RIBs, tents and awnings, sails and kites, waders, cracked buckets and other plastic containers, PVC curtain sides on trucks and warehouses.

DIRECTIONS: Ensure that the surface is clean and dry before using. Cut a suitable sized piece of TUFF Tape for your repair using good quality scissors or a sharp scalpel blade. Peel off the backing paper. Carefully position and then apply the TUFF Tape directly on top of the damage. Start at one edge and press the tape down gradually to avoid the entrapment of air bubbles. Once the TUFF Tape is in place rub it firmly with a smooth and hard object (such as the back of a spoon) to ensure the maximum adhesion to the substrate.

Stormsure ’TUFF Tape’ is a very strong, clear, self-adhesive, waterproof tape that is sold as individual pre-cut patches and strips of various shapes and sizes. TUFF Tape is made of a thin, but very tough, polyurethane film with a pressure sensitive adhesive and backing paper on the rear side. It has characteristics unlike many other tapes. It is waterproof and air tight. It is highly resistant to abrasion and very difficult to tear or puncture. It stretches and is elastic and it can withstand both heat and extreme cold without losing all its useful characteristics. TUFF Tape is very strong and can bind together items just by stretching the tape around the item and using the elasticity to pull the pieces tightly into place. When TUFF tape is applied to clothing it will go through regular washing machine cycles unaffected.

USES: Use TUFF Tape to quickly repair rips in waterproof clothing, ripped netting and fabrics, inflatable mattresses, canoes and RIBs, tents and awnings, sails and kites, waders, cracked buckets and other plastic containers, PVC curtain sides on trucks and warehouses.

DIRECTIONS: Ensure that the surface is clean and dry before using. Cut a suitable sized piece of TUFF Tape for your repair using good quality scissors or a sharp scalpel blade. Peel off the backing paper. Carefully position and then apply the TUFF Tape directly on top of the damage. Start at one edge and press the tape down gradually to avoid the entrapment of air bubbles. Once the TUFF Tape is in place rub it firmly with a smooth and hard object (such as the back of a spoon) to ensure the maximum adhesion to the substrate.

Adhesive for repairing all types of outdoor boots and shoes

This very special adhesive glue is one of the few products that can repair leaks, cracks or soles on fishing boots and oilskin trousers, as well as leather, sports and hiking boots.
Repairs are permanent, strong, waterproof, flexible and resistant to abrasion (even heel wear).

If you have stepped on a nail or punctured your boot with a tool, Stormsure glue is the perfect solution. You can plug the hole or patch the tear with this excellent product.

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete. 

A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS:
Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.
TIPS:
Mix with Stormcure Accelerator to reduce cure time to approximately 1 hour. Ensure there is no air left in the tube before replacing cap.
Store partly-used tubes in a deep freezer.

Glue for repairing all types of inflatable canoes, kayaks and all other sail boats.

This very special adhesive glue is one of the few products that can repair leaks, cracks and rips on all sail boats, canoes, kayaks of all shapes and sizes! Including inflatable toys and other equipment.
Repairs are permanent, strong, waterproof, flexible and resistant to abrasion (weather and water abrasion).

A perfect way to get you back into the water safely, Stormsure glue is the perfect solution. You can plug the hole or patch the tear with this excellent product.

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete. 
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS:
Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.
TIPS:
Mix with Stormcure Accelerator to reduce cure time to approximately 1 hour. Ensure there is no air left in the tube before replacing cap.
Store partly-used tubes in a deep freezer.

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete.
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS: Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.

TIPS: Store partly-used tubes in a deep freezer. Warm up to room temperature before use again.

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete.
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS: Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.

TIPS: Store partly-used tubes in a deep freezer. Warm up to room temperature before use again.

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete.
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS: Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.

TIPS: Store partly-used tubes in a deep freezer. Warm up to room temperature before use again.

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete. 
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS: Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.

TIPS: Store partly-used tubes in a deep freezer. Warm up to room temperature before use again.

Our flagship product, Stormsure Flexible Repair Adhesive, is a waterproof universal glue. It is highly versatile in all areas but is particularly useful in repairs to outdoor-wear and water sports equipment due to being flexible and extremely tough when cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in wellington boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and much more. 

An essential piece of kit for hikers, fishermen, equestrians, hunters, divers, campers, surfers, sailors etc!

Comes with disposable gloves.

DIRECTIONS

Using at room temperature. Clean the damaged area (sand the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, leaving at least a 5mm excess around it. Leave flat and allow to cure for 10-12 hours.

TIPS

Mix with Stormcure Accelerator to reduce cure time to approximately 1 hour. Ensure there is no air left in the tube before replacing cap. Store partly used tubes in a freezer.

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete.
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS: Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.

TIPS: Store partly-used tubes in a deep freezer. Warm up to room temperature before use again.

Adding a highly durable layer of water resistance on breathable fabrics, Gore-Tex® and regular rip stop nylon.

Also works on fleeces and wool clothing. This large capacity is best suited for distributing into smaller containers or in industrial & manufacturing settings.

Adding a highly durable layer of water resistance on breathable fabrics, Gore-Tex® and regular rip stop nylon. Also works on fleeces and wool clothing. This large capacity is best suited for distributing into smaller containers or in industrial & manufacturing settings.

Stormsure ’TUFF Tape’ is a very strong, clear, self-adhesive, waterproof tape that is sold as individual pre-cut patches and strips of various shapes and sizes. TUFF Tape is made of a thin, but very tough, polyurethane film with a pressure sensitive adhesive and backing paper on the rear side. It has characteristics unlike many other tapes. It is waterproof and air tight. It is highly resistant to abrasion and very difficult to tear or puncture. It stretches and is elastic and it can withstand both heat and extreme cold without losing all its useful characteristics. TUFF Tape is very strong and can bind together items just by stretching the tape around the item and using the elasticity to pull the pieces tightly into place. When TUFF tape is applied to clothing it will go through regular washing machine cycles unaffected.

USES: Use TUFF Tape to quickly repair rips in waterproof clothing, ripped netting and fabrics, inflatable mattresses, canoes and RIBs, tents and awnings, sails and kites, waders, cracked buckets and other plastic containers, PVC curtain sides on trucks and warehouses.

DIRECTIONS: Ensure that the surface is clean and dry before using. Cut a suitable sized piece of TUFF Tape for your repair using good quality scissors or a sharp scalpel blade. Peel off the backing paper. Carefully position and then apply the TUFF Tape directly on top of the damage. Start at one edge and press the tape down gradually to avoid the entrapment of air bubbles. Once the TUFF Tape is in place rub it firmly with a smooth and hard object (such as the back of a spoon) to ensure the maximum adhesion to the substrate.

EAN: 5060219660667

Stormsure ’TUFF Tape’ is a very strong, clear, self-adhesive, waterproof tape that is sold as individual pre-cut patches and strips of various shapes and sizes. TUFF Tape is made of a thin, but very tough, polyurethane film with a pressure sensitive adhesive and backing paper on the rear side. It has characteristics unlike many other tapes. It is waterproof and air tight. It is highly resistant to abrasion and very difficult to tear or puncture. It stretches and is elastic and it can withstand both heat and extreme cold without losing all its useful characteristics. TUFF Tape is very strong and can bind together items just by stretching the tape around the item and using the elasticity to pull the pieces tightly into place. When TUFF tape is applied to clothing it will go through regular washing machine cycles unaffected.

USES: Use TUFF Tape to quickly repair rips in waterproof clothing, ripped netting and fabrics, inflatable mattresses, canoes and RIBs, tents and awnings, sails and kites, waders, cracked buckets and other plastic containers, PVC curtain sides on trucks and warehouses.

DIRECTIONS: Ensure that the surface is clean and dry before using. Cut a suitable sized piece of TUFF Tape for your repair using good quality scissors or a sharp scalpel blade. Peel off the backing paper. Carefully position and then apply the TUFF Tape directly on top of the damage. Start at one edge and press the tape down gradually to avoid the entrapment of air bubbles. Once the TUFF Tape is in place rub it firmly with a smooth and hard object (such as the back of a spoon) to ensure the maximum adhesion to the substrate.

Stormsure ’TUFF Tape’ is a very strong, clear, self-adhesive, waterproof tape that is sold as individual pre-cut patches and strips of various shapes and sizes. TUFF Tape is made of a thin, but very tough, polyurethane film with a pressure sensitive adhesive and backing paper on the rear side. It has characteristics unlike many other tapes. It is waterproof and air tight. It is highly resistant to abrasion and very difficult to tear or puncture. It stretches and is elastic and it can withstand both heat and extreme cold without losing all its useful characteristics. TUFF Tape is very strong and can bind together items just by stretching the tape around the item and using the elasticity to pull the pieces tightly into place. When TUFF tape is applied to clothing it will go through regular washing machine cycles unaffected.

USES: Use TUFF Tape to quickly repair rips in waterproof clothing, ripped netting and fabrics, inflatable mattresses, canoes and RIBs, tents and awnings, sails and kites, waders, cracked buckets and other plastic containers, PVC curtain sides on trucks and warehouses.

DIRECTIONS: Ensure that the surface is clean and dry before using. Cut a suitable sized piece of TUFF Tape for your repair using good quality scissors or a sharp scalpel blade. Peel off the backing paper. Carefully position and then apply the TUFF Tape directly on top of the damage. Start at one edge and press the tape down gradually to avoid the entrapment of air bubbles. Once the TUFF Tape is in place rub it firmly with a smooth and hard object (such as the back of a spoon) to ensure the maximum adhesion to the substrate.

Stormproof is a high tech reproofing agent for use on all fabrics types and leather. Perfect for breathable fabrics, Gore-Tex® and regular rip stop nylon. It even works well on fleeces and wool clothing.

Adding a highly durable layer of water resistance on breathable fabrics, Gore-Tex® and regular rip stop nylon. Also works on fleeces and wool clothing. This large capacity is best suited for distributing into smaller containers or in industrial & manufacturing settings.

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete.
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS: Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.

TIPS: Store partly-used tubes in a deep freezer. Warm up to room temperature before use again.

For repairing small holes and rips in trampolines.

Waterproof • Durable • Clear • Non Flammable

Directions

Clean around the damaged area. For small holes, apply a thick film (1.5mm) of glue over the damaged surface plus an extra 10mm around it and leave to cure. To fix holes larger than 5mm, cover the underside of the hole with sticky tape. Apply the glue over the top surface as a thick film. (The tape holds the glue in place as it cures.) After it has cured, remove the tape and apply another thick film of glue on the underside. Always glue up to 10mm beyond the edges of the hole. Leave for 24 hours for a full cure.

Perfect for repairing your trampoline!

General mintenance kit for repairing all types of outdoor clothing and footwear.

This unique repair kit comes in a very convnient bag with clip, perfect for outdoor expditions.

This selection of very special adhesive glue, tape, oil and shampoo are one of the few products that can repair leaks, cracks and rips on all coats, trousers, gloves, hats, suits, goggles, glasses, boots, shoes and trainers and many more!
Repairs are permanent, strong, waterproof, flexible and resistant to abrasion (weather and water abrasion).

You don't need to buy new, repair your favourite items with this selection Stormsure products. You can plug the hole or patch the tear or clean materials with this excellent product.

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete. 
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS:
Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.
TIPS:
Mix with Stormcure Accelerator to reduce cure time to approximately 1 hour. Ensure there is no air left in the tube before replacing cap.
Store partly-used tubes in a deep freezer.

Pack of 4 colours - Clear • Black • Khaki • White

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete. 
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS: Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.

TIPS: Store partly-used tubes in a deep freezer. Warm up to room temperature before use again.

This adhesive is a conact adhesive: spread on to each of the sides to be stuck together and leave for 5 minutes until touch dry. Then press firmly together.

You can use just the glue (as a single component glue) on many fabrics, but the activator must be mixed with the adhesive when used to stick Hypalon fabric.

The glue is water proof and often used for making and repairing inflatable boats, RIBS and other marine craft.

These tins cannot be sent by Air Mail. It has to go by courier if you live outside the United Kingdom.

Choose Item SP70 instead.

Perfect alternative to Evo-Stik 8000.

Stormsure Flexible Repair Adhesive is a very strong general purpose adhesive and it can also be used as a surface sealant. It exhibits special characteristics unlike many adhesives as it is highly flexible and stretchy after it has cured but it remains very strong. It fills gaps well, it is suitable for use indoors and outdoors and in marine environments. The adhesive can be painted on top of a surface to make it waterproof, airtight or abrasion resistant. Stormsure adhesive can often be used to cover holes without a patch. A thick film of adhesive will make a good repair. If the glue will drip through the hole just place some sticky tape behind the hole before applying the glue. It can be removed once the glue has cured.

Stormsure Flexible Repair Adhesive bonds to virtually all surfaces including neoprene, rubber, leather, PVC, polyurethane, breathable and coated fabrics, wood, metal and more. It is ideal for repairing cracks in rubber wellington boots, hiking boots, loose soles, leaks in waders, rips in wetsuits, damaged horse rugs, holes in tents and canopies, leaks and splits inflatable items and many other items too. It can also be used for repairs to woodwork and furniture, roof tiles and concrete.
A tube of Stormsure Flexible Repair Adhesive is an essential part of a repair kit for hikers, DIY, fishermen, equestrians, hunters, divers, campers, surfers, sailors, engineers etc!
Comes with disposable gloves.

DIRECTIONS: Use the adhesive at room temperature. Clean the damaged area to remove dirt and grease (sandpaper the surface for best adhesion). Apply a generous amount of Stormsure Flexible Repair Adhesive to the damaged area, with at least a 5mm extra around the damaged area. Leave horizontal and allow to cure for 10-12 hours.

TIPS: Store partly-used tubes in a deep freezer. Warm up to room temperature before use again.